Wencon Exhaust Repair Kit
Wencon Exhaust Repair is a one-component steel cold weld product that can be used to repair cracks and holes in equipment exposed to temperatures up to 1300° C (2400°F)
Typical applications include engine heads, blocks and manifolds, as well as furnaces and boilers. Wencon Exhaust Repair is especially valuable in areas and situations where traditional heat welding cannot be accomplished.
- Resists temperatures up to 1300° C (2400° F)
- Resists direct flame contact
- Repairs cracks, fills holes and pits
- Quick cure when heated
- One component compound – no mixing, just stir
| Key technical data |
| Max temperature | Up to 1300°C (2400°F) |
| Consistency | fluid |
| Mixing ratio vol. | No mixing. Just stir the contens before use. |
| Apply with | See prod. sheet |
| Curing time | Initial curing 3-4 hours |
| Machineability | yes |
| Specific volume | 330 cm3 / kg |
| Product number | Product name | IMPA no. | ISSA no. |
| No. 1070 | Wencon Exhaust Repair Kit, 2x250g (2x0,23 lb) | 812340 | 75.553.25 |
Wencon Exhaust Repair Kit
Wencon Exhaust Repair Kit is a one-component steel cold weld product that can be used to repair cracks and holes in equipment exposed to temperatures up to 1300° C (2400°F).
Wencon Exhaust Repair can be grinded when cured. The compound has good adhesion on all metal surfaces. Wencon Exhaust Repair will not rust or oxidize and is resistant to chemicals.
Application areas
Wencon Exhaust Repair is especially suitable in areas and situations where traditional heat welding cannot be accomplished. Typical applications include engine heads, blocks and manifolds, as well as furnaces and boilers.
Note: It is important to note, that this product is designed only for external temporary repairs of cracks and leaks.
Packaging
- The Wencon Exhaust Repair Kit contains:
- Wencon Exhaust Repair Compound, 2 x 250 g (2 x 0,23 lb.)
- Reinforcement metal mesh, 10 x 50 cm (4 x 20 inch)
- Spatula
- Application data sheet
GENERAL DESCRIPTION
One component cold weld repair compound with particularly high temperature resistance.
SURFACE PREPARATION
The surface must always be as clean, dry and degreased.
Improved adhesion can be obtained by grinding or Grit blasting of the surface prior to application.
MIXING RATIO
No mixing is required. Just stir the content before use.
APPLYING
Apply a suitable amount of Exhaust Repair Compound in and around the leak.
Cut reinforcement wire mesh and fix it to the area of the repair. Hold the mesh in place using steel bands or steel wire.
Apply a second layer of repair compound and leave for initial curing 3-4 hours.
Heat up slowly to 95°C (203°F) for 15 minutes for full cure.
CURING TIME
Initial curing time after application of the first and second layer is 3-4 hrs.
Fully cured after 24 hrs. @ room temperature
OR apply heat: Slowly heat up 95°C (203°F) for 15 minutes for a full cure.
MACHINABLE
After curing the product can be machined.
SPECIFIC VOLUME
330 cm³ per kilogram (20,1 cu inch/kg)
TEMPERATURE RESISTANCE
Up to 1300°C (2400°F)
CHEMICAL RESISTANCE
The compound is resistant to oil, water, salt water and most diluted acids and alkalis as well as a range of solvents.
SHELF LIFE
At 20°C (68°F) : 3 years
HANDLING PRECAUTIONS
Read the Wencon Instruction for Use and the Material Safety Data Sheet.
| Brand | WENCON |
|---|---|
| Product Name | Wencon Exhaust Repair Kit |
Lucas Marine OÜ, Estonia
Department of international supplies
Phone: (+372) 5688 0639
Email: lm@lucas-marine.com